Sony SupportNEX-VG10

LA-EA1 Firmware Upgrade Ver.02 With NEX-VG10 (Microsoft Windows)

    Applicable Models
    About this download
    File Info
    System Requirements
    Install

    Applicable Models

    This information is for the following models:
    • NEX-VG10E
    • NEX-VG10
    • LA-EA1

    About this download

    Note: The download service for LA-EA1 Firmware Upgrade Ver.02 ended on February 28, 2023.

    Thank you for your continued interest in Sony products.

    Sony is always concerned about customer satisfaction and therefore is offering a software upgrade program for Mount Adaptor LA-EA1.

    Applicable firmware version
    Mount Adaptor LA-EA1 with firmware version Ver.01

    How to check the firmware version

    1. Attach the mount adaptor and the A-mount lens to the camera, then turn on the camera.
    2. Select Menu → Setup → Version on the camera.
    3. The firmware version is displayed. If your firmware version is Ver.02 or later, the upgrade is not required.

    Improvements after firmware upgrade
    Support for the autofocus function when A-mount lens is attached to the camera.

    *The following SAM lenses and SSM lenses are supported.

    SAM lenses

    • DT18-55mm F3.5-5.6 SAM [SAL1855]
    • 28-75mm F2.8 SAM [SAL2875]
    • DT55-200mm F4-5.6 SAM [SAL55200-2]
    • DT30mm F2.8 Macro SAM [SAL30M28]
    • DT35mm F1.8 SAM [SAL35F18]
    • DT50mm F1.8 SAM [SAL50F18]
    • 85mm F2.8 SAM [SAL85F28]

    SSM lenses

    • Vario-Sonnar T* 16-35mm F2.8 ZA SSM [SAL1635Z]
    • Vario-Sonnar T* 24-70mm F2.8 ZA SSM [SAL2470Z]
    • Distagon T* 24mm F2 ZA SSM [SAL24F20G]
    • 70-200mm F2.8 G [SAL70200G]
    • 70-300mm F4.5-5.6 G SSM [SAL70300G]
    • 70-400mm F4-5.6 G SSM [SAL70400G]
    • 300mm F2.8 G [SAL300F28G]

    * With an A-mount lens attached, the autofocus speed will be slower than when an E-mount lens is attached. (It takes approximately 2 to 7 seconds (based on Sony’s measurement standard). It may vary depending on the subjects or brightness of the shooting environments.)

    * Firmware upgrade of the Interchangeable Lens Digital HD Video Camera Recorder NEX-VG10 (sold separately) is also required. 

    System Requirements

    Supported OS

    • Windows® XP* SP3
    • Windows® Vista** SP2
    • Windows® 7

      * 64-bit and Starter editions are not supported.
      ** Starter edition is not supported.

    Other system requirements

    • Hard disk space: 200MB or more
    • RAM: 512 MB or more
      * Please close all other application software before upgrading the firmware.

    Other Items

    • USB cable supplied with the camera
    • Power source for the camera

      Fully charged rechargeable battery pack NP-FV70 or NP-FV100(sold separately) or AC adaptor AC-PW10AM.

      Note: The upgrade can be performed only when the remaining battery level is(three marks) or more. We recommend that you use a fully charged battery or the AC adaptor AC-PW10AM.

    Available Download
    File name: LA-EA1V2_Update1011a.exe
    File size: 2.03 MB (2,131,344 bytes)
    Updated on: 18th November 2010

    File Info

    File Name

    • LA-EA1 Firmware Upgrade Ver.02 With NEX-VG10 (Microsoft Windows)

    File Version

    • Ver.02

    File Size

    • 2.03MB

    Release Date

    • 2010-11-18

    System Requirements

    • Windows 7
    • Windows Vista
    • Windows XP

    Install

    Details

    IMPORTANT:

    • When performing the firmware upgrade, please use a fully charged rechargeable battery pack NP-FV70 or NP-FV100(sold separately) or AC adaptor AC-PW10AM.

    • Do not remove the battery or AC adaptor during the upgrade; otherwise, the camera may become inoperable due to the sudden power shutdown.

    Firmware Upgrade Instructions

    1. Double-click LA-EA1V2_Update1011a.exe to start up Firmware Updater.
       

    2. Attach the mount adaptor and the A-mount lens to the camera, then turn on the camera.

    3. Connect the camera to the computer with the supplied USB cable.
      Note: When the camera is connected to the computer, the LCD screen of the camera turns off. Please proceed to the next step.

    4. Confirm is displayed on the task tray at the lower right corner of the computer screen.

    5. After confirming the above, click Next on Firmware Updater.
      Figure 1 appears on Firmware Updater and Figure 2 appears on the LCD screen of the camera.

      Figure 1: Firmware Updater


      Figure 2: Camera’s LCD screen


      Note: From this step onwards, never turn off the camera until the firmware upgrade is completed.


    6. After confirming the screens on Figures 1 and 2, click Next. The current version and the version after the upgrade appear on the lower left part of the screen.

      Figure 3: Upgrade is required



      If "Current version: Ver.2" appears on the screen(Figure 4), the upgrade is not required. According to the message, stop the USB connection and click Finish. Turn off the camera, remove the battery pack or the AC adaptor, and then turn on the camera again.

      Figure 4: Upgrade is not required


    7. Clickon the task tray at the lower right corner of the computer screen to stop the USB connection.

      Note: Please keep the USB cable connected even after stopping the USB connection on the computer with the above operation.


    8. Press the center of the control wheel to reset the camera.

      Figure 5: Camera’s LCD screen


      Figure 6: Camera control wheel

      Note: The screen turns off when the center of the control wheel is pressed. Please proceed to the next step.

    9. After resetting, reconnection of the camera is verified, and the screen on Figure 7 appears.

      Figure 7


    10. Click Run to transfer the firmware upgrade. The progress bar appears while upgrading (approximately 10 seconds).

      Note: Never turn off the camera nor disconnect the USB cable while upgrading.

    11. When the transfer is completed, the screen on Figure 8 appears. Click Finish and disconnect the USB cable.

      Figure 8


    12. The updating procedure will start, and Figure 9 will be displayed. The progress bar appears while upgrading.

      Figure 9: Updating the mount adaptor


    13. When the upgrade is completed, the screen on Figure 10 appears.
      Turn off the camera, remove the battery pack or the AC adaptor, and then turn on the camera again.

      Figure 10: Complete the upgrade of the mount adaptor

    Check the firmware version

    1. Select Menu → Setup → Version on the camera.

    2. The firmware version is displayed. The firmware upgrade was completed successfully if Ver.02 is displayed.